Tracking cookies

To make our website even easier and more personal, we use cookies (and similar techniques). With these cookies we and third parties can collect information about you and monitor your internet behavior within (and possibly also outside) our website. If you agree with this, we will place these tracking cookies.

Yes, I give permissionNo thanks
Categories
https://www.dehaco.nl/en/service/safety-service
Search
Shopping cart

    Dehaco Safety Service

    Calibration and repair service

    Om uw meetapparatuur te testen en opnieuw af te stellen bieden wij een kalibratieservice voor de volgende producten:

    • Monitors
    • Masks
    • Gas detection
    • Air movers
    • Decontamination units
    • Water management systems
    • Breathing compressors
    • Hand tools
    • Milling machines
    • Vacuum cleaners
    • Floor strippers
    • Independent air systems

    Our products are designed to measure with high precision. However sometimes accuracy can be reduced due to conditions such as improper storage, temperature fluctuations or misuse. We therefore recommend you to have your equipment regularly calibrated. At least once a year. In certain cases it may be necessary to have tools calibrate more frequently. Use your internal quality policy to check the requirements for your company. In certain cases it may be necessary to have tools calibrate more frequently. Use your internal quality policy to check the requirements for your company.

    ISO 9001 certified in 3 steps

    We are certified for the ISO 9001 quality management system. We offer a service in three steps:

    1. Verification of accuracy

    We compare the accuracy of your tools with the accuracy as defined in the "manufacturer's specifications" in the user manual.

    2. Adjustment, cleaning and maintenance

    If a product does not meet the original specificaitons, we can adjust it and make it accurate again. We also clean and inspect the product and ensure that it works correctly before we send it back to you.

    3. Documentation

    We also add a cerfificate confirming that the tool meets the requirements.

    Fit-test service

    The goal of respiratory protection is that an employee is optimally protected against hazardous substances. But how do you know for sure that the mask you wear also offers the right protection?

    What can Dehaco do for you?

    Dehaco thinks it is important to let your employees experience when a product works well. For this reason, Dehaco offers the fit test. The fit test can be performed at the Dehaco office in Lisserbroek and from 10 people on location.

    Fit-test on location?

    With a minimum of 10 people, the fit test can also be carried out on location within the Benelux. If you want to use this service, the location must in any case meet the following conditions:

    • The space must have an area of approximately 4 x 3 meters.
    • Preferably the location is on the ground floor.
    • The room must not be ventilated (or the vertilation must be able to be switched off).
    • The room must be equipped with a power connection.
    • There must be a waiting area nearby the fit test room.

    We would like to point out that you can not eat, drink and / or smoke an hour before the fit test. In addition, you must have shaved.

    We are certified

    Dehaco is a SafetySign® approved company for face fittesting :

    Technical support

    We are always looking for the best solutions and the best possible service. We try to keep your product or machine in optimum condition at the lowest possible cost. We are always available for telephone support or on-site service.

    DEHACO SERVICE POINT OF HILTI

    Dehaco has been working with Hilti asbestos tools for a number of years now. For example, Dehaco offers maintenance and repair under Hilti's warranty conditions for a number of their products. These are the TE 500 demolition hammer, TE 700 demolition hammer, TE 800 demolition hammer, TE 1000 demolition hammer, WSR 1300 reciprocating saw and DG 150 concrete grinding machine. Dehaco is the only company in the world with this cooperation. Do you have any questions about this or do you want more information? Please contact us on +31 (0)88 20 20 600.

    Calamity service

    088 - 20 20 600


    Technical support

    Robbert Noppe

    Techn. support specialist

    Phone +31(0)88 20 20 652

    E-mail rnoppe@dehaco.nl

    Planning

    Ferry van der Zwet

    Planning Safety

    Phone +31 (0)88 20 20 653

    E-mail fvanderzwet@dehaco.nl